Shock absorber replacement

Shock absorber replacement
Shock absorber replacement
Difficulty	Expert
Duration	60 minutes
For series	Some one-drum Z+Any machine released with or after the RZ line, i.e. RZ/RV/EZ/EV/SF/SE and MZ/ME/MF/MH machines. machines SE
Tools	JIS phillips #2 screwdriver Metric hex wrenches
Parts	046-15009 1 × Shock absorber 046-15008 1 × Shock absorber bracket (if not already installed)

This is the draft of an article, it is incomplete or in-progress.

You can help by contributing to missing sections, editing existing material, or helping to migrate this page from linked sources.

On some models of one-drum Z+Any machine released with or after the RZ line, i.e. RZ/RV/EZ/EV/SF/SE and MZ/ME/MF/MH machines. machines, a small black rubber shock absorber helps soften the impact of the pressure lever (used to move the pressure roller up and down for each rotation of the drum. Over time, the shock absorber wears down—when it is fully deteriorated the riso can no longer be used for printing. The symptoms of this issue are different depending on if the pressure roller is stuck in the up position or the down position.

If the pressure roller is stuck in the down position, pages will feed partially into the riso, making it into the area above or just past the pressure roller, where they will halt and trigger a paper jam. These pages were never pressed onto the surface of the drum, so they will have no image printed on them.
If the pressure roller is stuck in the up position, pages will come out over inked, with ink spread across the whole back of the sheet and continuous ghosting on the front. Furthermore the drum will be difficult or impossible to remove, as the pressure roller will be dragging against it as it is pulled out of the risograph.

The shock absorber can be replaced, but it is a difficult task which involves partially disassembling the main drive of the risograph, in the back of the machine.

A worn shock absorber (in its holder) and a new one. Often by the time of printing failure, there is little or nothing left of the rubber absorber itself.

Background

Not all one-drum Z+Any machine released with or after the RZ line, i.e. RZ/RV/EZ/EV/SF/SE and MZ/ME/MF/MH machines. machines use a shock absorber—all models do, but only some machines have it. Known models which use a shock absorber are as follows:

EZ200	EZ201	EZ220	EZ221	EZ230	EZ231
EZ300	EZ301	EZ330	EZ331	EZ370	EZ371
EZ390	EZ391	EZ570	EZ571	EZ590	EZ591

	RZ970	RZ977	RZ990	RZ997	RZ1070	RZ1090

	SF5030	SF5130	SF5230	SF5330	SF5350	SF5430
	SF5450	SF9350	SF9450	SF9490

The presence of shock absorbers on EVSE machines is currently unknown/unconfirmed. Which models have them also needs verification.

Two versions of shock absorber

Older machines sometimes have an older model of shock absorber installed, which was adhered to a small rounded plate, rather than held within a mounting bracket, as the new ones are. These older shock absorbers are no longer available as replacement parts, however the new mounting bracket is interchangeable, after which the new shock absorbers can be used. If a machine does not have the mounting bracket (part no. 046-15008) it will need to be acquired along with the shock absorber (part no. 046-15009) before the repair can be made.

Confirming diagnosis

The easiest way to confirm the diagnosis of a deteriorated shock absorber is to look for the black rubber debris which will collect on the base plate in the back of the riso, beneath where the shock absorber is mounted. This can be seen just by removing the back cover of the risograph (4 screws) (though it is easier to see if the circuit board panels are opened up as well—by removing the screws marked with arrows on the brackets).

The back of the machine, with the area to check highlighted.
Rubber fragments from the damaged shock absorber.

Replacement procedure

First the riso must be setup so that access to shock absorber area is a little easier—then all work will be done with the riso off and unplugged. After replacement, proper calibration of the pressure lever should be checked.

Setting up the risograph

Turn the riso on in test mode.
Remove the drum and close the front door.
Get the machine into the main test mode area by pressing the STOP button until the numeric display reads 0 or 0000.
If this machine has adjustable density, run the pressure lever maintenance position test mode by punching in 908 + START and waiting for the test to end (about 5 seconds, will finish with a beep).
Turn the riso off and unplug it.

From this point forward, the riso should remain off and unplugged until the repair is finished and the machine is fully reassembled.

Accessing the mechanics

Remove the back cover of the riso (4 screws).
Open up the PCB bracket(s)—these are the metal panels that hold the large circuit boards at the back of the risograph.
1. Each bracket will have between 3–5 screws holding it in place, which are each marked with an engraved arrow and the total number of screws holding in that assembly (e.g. a mark of "4→" indicates that this is one of four screws that need to be removed). These screws are usually located somewhere near the corners of the panels.
2. Once the screws are removed the bracket(s) will swing open to the side like cabinet doors.

The 4 screws holding on the back cover.
In this model—an 5130—each PCB bracket is held on with 4 screws.

Remove the "pressure spring" (largest spring visible) on the back left side of this area.
- On machines with adjustable density, the spring should already be fairly loose (test mode 908 raised up the lower hook of the spring to remove tension on it).
- On machines which do not have adjustable density (or if the maintenance positioning test mode wasn't run) the pressure lever will have to be lowered manually before the spring can be removed.

Manual lowering of the pressure lever

The pressure spring is under a great deal of tension, and it can be dangerous to remove it by force, without first lowering the pressure lever. Use caution in these steps to avoid having the spring snap out or pinch hands/tools.

The pressure lever and spring are the mechanism which raise the pressure roller up to the surface of the drum when printing. As the lever is lowered (rotating counter-clockwise as viewed from the back), the pressure roller raises up to the drum, pressed up with force from the pressure spring). As it is raised, the pressure roller lowers (this happens as the clamp passes under the drum with every rotation.

The pressure lever is held in place with a small hook, beneath it to the left—this hook cannot just be pulled out while the spring is pulling on the pressure lever, or the lever will snap down rapidly. The proper method of removal is as follows.

Brace one hand on the top of the main drive cover (the middle metal "cage" with all the triangular cutouts), and with the thumb, lift up the tab at the top end of the pressure roller. In this way the technician is holding/managing all the force of the spring, not the hook.
While the force is being held, with the other hand, pull the hook out to the left (with the pressure lever manually lifted up, there should no longer be any force on the hook).
With the hook held out of the way, slowly lower the pressure lever, removing the tension on the spring.
Once the spring is hanging loosely, remove it.